水厂常规工艺去除有机物和总磷

有机物、总磷是我国地表水源主要污染物,涉及范围广,污染浓度高,是影响水厂出水安全的重要因素。以某水厂净水系统为依托,分析水厂常规工艺对有机物和总磷的去除效果及影响因素。研究表明,地表水源水厂所采用的混凝+沉淀+过滤+消毒的传统工艺对有机物的去除率不高,在22.1%～61.3%之间,平均去除率为38.3%;其中,混凝沉淀是常规工艺中去除CODMn的关键环节,占总去除效果的43%～68%,过滤环节去除率约为10%;温度和混凝剂投加量是影响CODMn去除效果的主要因素。常规工艺对总磷的去除效果较好,去除率约为60%～90%,冬季略低,其他季节略高;混凝沉淀单元与过滤单元对总磷均有较好的去除效果,去除率分别为25%～77%和40%～76%。在当前水质条件下,水厂现行工艺可满足常规状况下有机物和总磷的去除需要。     

不同改性方式对控释碳源材料脱氮性能的影响

以玉米淀粉(S)为碳源,聚乙烯醇(P)为骨架载体,根据是否用硼酸(B)和硫酸钠(N)做改性处理,制备了GSP、GSP-N、GSP-B和GSP-BN 4种控释碳源材料,研究N、B和BN 3种改性方式对碳源材料脱氮性能的影响。在添加4种碳源的静态实验中,硝酸盐氮去除率均在96.1%以上。碳源材料的改性对硝酸盐氮的降解情况影响不明显,但对脱氮过程中TOC、亚硝酸盐氮、氨氮和TN浓度的变化有不同程度的影响。以TOC、亚硝酸盐氮、氨氮和TN为指标,N、BN和B 3种改性方式综合效益指数分别为5.62、4.6和1.92,硫酸钠(N)改性处理对提高控释碳源材料整体性能具有最佳效果。     

Fine Particle Removal Performance of a Two-Stage Wet Electrostatic Precipitator Using a Nonmetallic Pre-Charger

ABSTRACT

A novel two-stage wet electrostatic precipitator (ESP) has been developed using a carbon brush pre-charger and collection plates with a thin water film. The electrical and particle collection performance was evaluated for submicrometer particles smaller than 0.01～0.5 μm in diameter by varying the voltages applied to the pre-charger and collection plates as well as the polarity of the voltage. The collection efficiency was compared with that calculated by the theoretical models. The long-term performances of the ESP with and without water films were also compared in tests using Japanese Industrial Standards dust. The experimental results show that the carbon brush pre-charger of the two-stage wet ESP had approximately 10% particle capture, while producing ozone concentrations of less than 30 ppb. The produced amounts of ozone are significantly lower than the current limits set by international agencies. The ESP also achieved a high collection rate performance, averaging 90% for ultrafine particles, as based on the particle number concentration at an average velocity of 1 m/sec corresponding to a residence time of 0.17 sec. Higher particle collection efficiency for the ESP can be achieved by increasing the voltages applied to the pre-charger and the collection plates. The decreased collection efficiency that occurred during dust loading without water films was completely avoided by forming a thin water film on the collection plates at a water flow rate of 6.5 L/min/m2 Zukeran, A., Ikeda, Y., Ehara, Y., Matsuyama, M., Ito, T., Takahashi, T., Kawakami, H. and Takamatsu, T. 1999. Two-Stage-Type Electrostatic Precipitator Re-entrainment Phenomena under Diesel Flue Gases. IEEE. Trans. Ind. Appl, 35: 346–351. [Crossref], [Web of Science ®] , [Google Scholar].

IMPLICATIONS Current two-stage electrostatic precipitators (ESPs) have several technical problems such as a drop in collection efficiencies by small-particle re-entrainment during rapping and corrosion of metallic electrodes of the ESPs by corrosive gases. This paper evaluates a novel two-stage ESP that uses a nonmetallic pre-charger and water film collection plates to avoid the above mentioned problems of other ESPs. This ESP can be used not only for industrial applications but also for residential purposes because it has a high removal performance for fine particles with low ozone generation and maintains its efficiency due to the continuous cleaning of the collection plates with water film.     

对水污染源在线监测设备系统集成的思考

简述了水污染源在线监测设备系统集成的必要性,分析了目前系统集成中存在的问题,以及应采取的对策。按照国家有关规范要求,对现场端的在线监测设备进行科学的综合布局,并从采水、配水、预处理、控制、分析、数据采集与传输、辅助等构成单元,提出了有关水污染源在线监测设备系统集成的方案。     

Heat shock protein 47 stress responses in Chinese hamster ovary cells exposed to raw and reclaimed wastewater

As wastewater reclamation and reuse becomes more widespread, risks of exposure to treated wastewater increase. Moreover, an unlimited number of pollutants can be identified in wastewater. Therefore, comprehensive toxicity assessment of treated wastewater is imperative. The objective of this study was to perform a comprehensive toxicity assessment of wastewater treatment systems using stress response bioassays. This powerful tool can comprehensively assess the toxicity of contaminants. In this study, samples from conventional activated sludge treatment, membrane bioreactors (MBRs) with different pore sizes and sludge retention times (SRTs), rapid sand filtration, coagulation, nano-filtration (NF) and reverse osmosis (RO) were investigated. The results of stress response bioassays confirmed that the secondary effluent showed higher stress response than influent indicating that biological treatment generates toxic compounds. The results obtained from molecular weight fractionation of water samples demonstrated that organic matter with a higher molecular weight fraction (>0.1 μm) causes toxicity in secondary effluent. Furthermore, supernatant from MBR reactors showed toxicity regardless of SRT. On the other hand, stress response was not detected in MBR permeates except for an MBR equipped with a larger pore size membrane (0.4 μm) and with a short SRT (12 days). While rapid sand filtration could not remove the toxic compounds found in secondary effluent, coagulation tests, operated at an appropriate pH, were effective for reducing stress response in the secondary effluent. Experimental findings also showed that stress response was not detected in cases of NF and RO permeate subsequent to MBR treatment.     

Pollution characteristics of volatile organic compounds in the atmosphere of Haicang District in Xiamen City, Southeast China

The compositions, spatial distributions, seasonal variations and ozone formation potential (OFP) of volatile organic compounds (VOCs) were investigated in the atmosphere of Haicang District, Xiamen City, Southeast China. Twenty-four types of VOCs were measured in this study, and ethanol, methylene chloride, toluene, ethyl acetate and isopropyl alcohol were the abundant species based on concentration rank. The concentrations of total VOCs (TVOCs) in industrial areas were higher than those in residential and administrative areas and background site. For industrial areas, the TVOCs concentrations in summer were higher than those in winter, which might result from higher emissions from industrial activities because of stronger evaporation in summer. In contrast, non-industrial areas showed higher concentrations in winter due to the unfavorable meteorological conditions. The spatial distribution of BTEX (benzene, toluene, ethylbenzene and xylene) followed the order of industrial areas > residential and administrative areas > background site, and the concentrations in summer were lower than those in winter for most sites. The high ratios (8.9-14.0) of T/B in this study indicated that industrial emissions were the main sources in this district. X/B ratios were used to assess the ages of air parcels and provided evidence of the transport of air parcels among these sites. Total OFP (TOFP) showed the trend of increase with the increase of TVOCs, and toluene was found as the major contributor to TOFP.     

Occurrence and removal of endocrine-disrupting chemicals in wastewater treatment plants in the Three Gorges Reservoir area, Chongqing, China

Concentrations of six endocrine-disrupting compounds (EDCs), bisphenol A (BPA), estrone (E(1)), 17β-estradiol (E(2)), estriol (E(3)), 17α-ethynylestradiol (EE(2)) and diethylstilbestrol (DES), were assessed in influents, effluents and excess sludge in ten municipal wastewater treatment plants (WWTPs) in the Three Gorges Reservoir (TGR) area, Chongqing, China. Three types of activated sludge treatment processes, oxidation ditch (OD), reversed anaerobic-anoxic-oxic (rA(2)/O) technology and sequential batch reactor (SBR), were used in the surveyed WWTPs. These WWTPs were all combined landfill leachate-sewage treatment plants. All analytes were extracted by solid-phase extraction (SPE) in the dissolved phase and by accelerated solvent-based extraction (ASE) in sludge. Gas chromatography-mass spectrometry (GC-MS) was employed for the analysis of EDCs. Among these EDCs, BPA was the most frequently detected and abundant compound (100.0-10566.7 ng L(-1), 15.5-1210.7 ng L(-1) and 85.0-2470.4 ng g(-1) with respect to the influents, effluents and excess sludge samples). The greatest levels of steroidal estrogens in municipal influents were observed in E(3) which were all >100 ng L(-1), followed by E(1) (42.2-110.7 ng L(-1)) and E(2) (7.4-32.7 ng L(-1)), and in the effluents and sludge were E(1) > E(3) > E(2) which were all <31 ng L(-1) and 105 ng g(-1), respectively. Regarding synthetic estrogens, EE(2) was frequently detected in the influents, occurring below 50 ng L(-1), while DES was not detected at all. A high correlation coefficient was observed between the leachate-sludge ratio and concentrations of influent EDCs, and it was statistically significant (i.e., R > 0.65, P < 0.05), but removal efficiency of the EDCs did not show significant differences with OD, rA(2)/O and SBR processes. Furthermore, modification of treatment technology as well as operational parameters, such as hydraulic retention time (HRT), sludge retention time (SRT) and disinfection process (DP), were recommended to further eliminate the residual EDCs.     

Sulfur deposition simulations over China, Japan, and Korea: a model intercomparison study for abating sulfur emission

In response to increasing trends in sulfur deposition in Northeast Asia, three countries in the region (China, Japan, and Korea) agreed to devise abatement strategies. The concepts of critical loads and source?Creceptor (S?CR) relationships provide guidance for formulating such strategies. Based on the Long-range Transboundary Air Pollutants in Northeast Asia (LTP) project, this study analyzes sulfur deposition data in order to optimize acidic loads over the three countries. The three groups involved in this study carried out a full year (2002) of sulfur deposition modeling over the geographic region spanning the three countries, using three air quality models: MM5-CMAQ, MM5-RAQM, and RAMS-CADM, employed by Chinese, Japanese, and Korean modeling groups, respectively. Each model employed its own meteorological numerical model and model parameters. Only the emission rates for SO₂ and NO_x obtained from the LTP project were the common parameter used in the three models. Three models revealed some bias from dry to wet deposition, particularly the latter because of the bias in annual precipitation. This finding points to the need for further sensitivity tests of the wet removal rates in association with underlying cloud?Cprecipitation physics and parameterizations. Despite this bias, the annual total (dry plus wet) sulfur deposition predicted by the models were surprisingly very similar. The ensemble average annual total deposition was 7,203.6?±?370 kt S with a minimal mean fractional error (MFE) of 8.95?±?5.24?% and a pattern correlation (PC) of 0.89?C0.93 between the models. This exercise revealed that despite rather poor error scores in comparison with observations, these consistent total deposition values across the three models, based on LTP group's input data assumptions, suggest a plausible S?CR relationship that can be applied to the next task of designing cost-effective emission abatement strategies.     

Characterization of dissolved organic matter in the rhizosphere of hyperaccumulator Sedum alfredii and its effect on the mobility of zinc

Pot experiments were performed to investigate the characteristics of dissolved organic matter (DOM) in the rhizosphere soil of hyperaccumulating ecotype (HE) and a non-hyperaccumulating ecotype (NHE) of Sedum alfredii and its effects on the mobility of zinc (Zn). DOM was fractionated using XAD resins into six fractions. The acid fraction was the predominant component of DOM in the rhizosphere of S. alfredii, with hydrophilic acid (HiA), hydrophilic base (HiB), and hydrophilic neutral (HiN) in HE-DOM being 1.6, 1.9, and 1.2 times higher respectively, as compared to NHE-DOM. ATR-FTIR results showed that DOM in the rhizosphere of S. alfredii consisted of a mixture of hydroxylated and carboxylic acids, and HE-DOM exhibited more CO, OH, CC and CO functional groups than NHE-DOM. Resin equilibration experiment results indicated that DOM from the rhizosphere of both ecotypes of S. alfredii had the ability to form complexes with Zn, whereas the degree of complexation was significantly higher for HE-DOM (60%) than NHE-DOM (42%). The addition of HE-DOM significantly (P < 0.05) increased the solubility of four Zn minerals while NHE-DOM was not as effective at the same concentration. It was concluded that DOM derived from the rhizosphere of hyperaccumulating ecotype of S. alfredii could significantly increase Zn mobility through the formation of soluble DOM-metal complexes, this might be one of the important mechanism by which S. alfredii is involved in activating metal in rhizosphere.     

Photoelectrocatalytic degradation of recalcitrant organic pollutants using TiO2 film electrodes: an overview

Photoelectrocatalytic (PEC) technology involved applying an electrical bias to a TiO₂ film electrode, has been widely applied to the degradation of refractory organic pollutants, owing to its high degradation efficiency. This paper reviews recent developments in the PEC degradation of recalcitrant organic contaminants using a TiO₂ film electrode. The preparation and application of various TiO₂ film electrodes have been investigated, as well as the parameters that influence PEC activity such as the crystal structure, the film thickness and substrate material, the applied electrical bias, the solution pH and conductivity. The improvement of PEC activity by doping the TiO₂ film electrode with metal and non-metal ions has been discussed. The mechanism and kinetics for the PEC degradation of organic pollutants have also been highlighted.